Size: 254 x 203 mm / 10" x 8"
fits: Makergear M2 and Makergear M3
*may fit: CraftBot Plus Pro
The Pre-Installed Flexible Build System includes:
- 1 Wham Bam Flexi Magnetic Base (high temp-resistant up to 150 degrees with high temp 3M adhesive)
- 1 Wham Bam Flexi Build Plate (spring steel) with pre-installed Wham Bam Custom Formulated PEX Build Surface
- 1 Steel Wool 000 (for prepping your PEX Build Surface)
The Pre-Installed Double Wham includes:
- 1 Wham Bam Flexi Magnetic Base (high temp-resistant up to 150 degrees with high temp 3M adhesive)
- 2 Wham Bam Flexi Build Plate (spring steel) with pre-installed Wham Bam Custom Formulated PEX Build Surface
- 1 Steel Wool 000 (for prepping your PEX Build Surface)
For more information on this product, click here: Flexible Build System
View the full chart of filament settings on PEX
*Attention: It is the buyer’s responsibility to be sure the size selected will work on your machine. Measure your bed, do not rely on build volume and see if you are happy with the size before ordering. Please keep in mind that on one side you will have 2 tabs that stick out another 15mm. Wham Bam is not responsible for mistaken order sizes. Learn more about machine fits HERE.
**It is the buyer’s responsibility to pay any taxes and import duties. No refunds of uncollected customs packages.
PEX Build Surface
Nothing has made removing prints from the bed easier. I got this as a gift and I would never go back. Say goodbye to the dreaded bed scraping to remove tough prints.
I have an Ender 5 plus that I've had lots of problems trying to get prints to stick to. The original glass bed was not sticky enough, a sheet of g10 was not sticky enough (even when roughed up with sandpaper), and a sheet of zebra skin was a bit too sticky. The wham bam PEX is perfect, though it took a few heating+cooling cycles to reach prime stickiness. I've only had one failed print since switching (and the failure happened in a known low spot on the bed). Highly recommend.
This build plate is great , I have no adhesion issues with anything.So far tried PLA,PETG ,ASA,PETG CF.
Thanks for the great product.
I have older machines that are absolute workhorses.
But the Taped unremovable plate made life difficult when the tape was new, prints had to be yeated out of the machine.
Now I just wait for the plate to cool, and the print just gently pops off the WHAMBAM PEX plate.
Also worth noting, I havent had the need to use a brim or raft for supports since getting the PEX plate for these machines.
The adheasion is incredible!
PEX Build Surface
Nothing has made removing prints from the bed easier. I got this as a gift and I would never go back. Say goodbye to the dreaded bed scraping to remove tough prints.
I have an Ender 5 plus that I've had lots of problems trying to get prints to stick to. The original glass bed was not sticky enough, a sheet of g10 was not sticky enough (even when roughed up with sandpaper), and a sheet of zebra skin was a bit too sticky. The wham bam PEX is perfect, though it took a few heating+cooling cycles to reach prime stickiness. I've only had one failed print since switching (and the failure happened in a known low spot on the bed). Highly recommend.
This build plate is great , I have no adhesion issues with anything.So far tried PLA,PETG ,ASA,PETG CF.
Thanks for the great product.
I have older machines that are absolute workhorses.
But the Taped unremovable plate made life difficult when the tape was new, prints had to be yeated out of the machine.
Now I just wait for the plate to cool, and the print just gently pops off the WHAMBAM PEX plate.
Also worth noting, I havent had the need to use a brim or raft for supports since getting the PEX plate for these machines.
The adheasion is incredible!