Due to a holiday, our China fulfillment center will be closed through October 9th.

PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)
PEX Build Surface (0.19mm)

PEX Build Surface (0.19mm)

Regular price
$10.00
Sale price
$5.00
Quantity must be 1 or more

**This is a closeout item**

We have developed the Wham Bam PEX Build Surface from a specially formulated polymer with a higher melt point than PEI that attracts most any filament without damaging the sheet. Prints easily pop off once cooled and flexed. This thinner version of our PEX build surface is 0.19mm thick and pre-backed with 3M adhesive so it takes seconds to install.

Please note that some of our users find this thinner version of PEX (0.19mm) is not as suitable for PETG as our standard version (0.35mm), if using PETG we suggest using a glue stick as a barrier to avoid bonding and possible chipping during part removal.

View the full chart of filament settings on PEX

Here is an article on the differences, settings, tips, and maintenance for all our build surfaces.

*Please confirm bed size on your actual machine prior to ordering. Wham Bam is not responsible for mistaken sizes ordered. See our sizing guide.

*It is the buyer’s responsibility to pay any taxes and import duties. No refunds of uncollected customs packages.

Customer Reviews

Based on 275 reviews
92%
(253)
7%
(20)
1%
(2)
0%
(0)
0%
(0)
B
Bryan Gateb

PEX Build Surface

V
V.I.
Best quality of life improvement

Nothing has made removing prints from the bed easier. I got this as a gift and I would never go back. Say goodbye to the dreaded bed scraping to remove tough prints.

C
Customer
Slam dunk for large print beds

I have an Ender 5 plus that I've had lots of problems trying to get prints to stick to. The original glass bed was not sticky enough, a sheet of g10 was not sticky enough (even when roughed up with sandpaper), and a sheet of zebra skin was a bit too sticky. The wham bam PEX is perfect, though it took a few heating+cooling cycles to reach prime stickiness. I've only had one failed print since switching (and the failure happened in a known low spot on the bed). Highly recommend.

R
Robert Larrarte
Great product

This build plate is great , I have no adhesion issues with anything.So far tried PLA,PETG ,ASA,PETG CF.
Thanks for the great product.

J
Jayson Smith
Billiant! Made my life easier!

I have older machines that are absolute workhorses.
But the Taped unremovable plate made life difficult when the tape was new, prints had to be yeated out of the machine.
Now I just wait for the plate to cool, and the print just gently pops off the WHAMBAM PEX plate.
Also worth noting, I havent had the need to use a brim or raft for supports since getting the PEX plate for these machines.
The adheasion is incredible!

Customer Reviews

Based on 275 reviews
92%
(253)
7%
(20)
1%
(2)
0%
(0)
0%
(0)
B
Bryan Gateb

PEX Build Surface

V
V.I.
Best quality of life improvement

Nothing has made removing prints from the bed easier. I got this as a gift and I would never go back. Say goodbye to the dreaded bed scraping to remove tough prints.

C
Customer
Slam dunk for large print beds

I have an Ender 5 plus that I've had lots of problems trying to get prints to stick to. The original glass bed was not sticky enough, a sheet of g10 was not sticky enough (even when roughed up with sandpaper), and a sheet of zebra skin was a bit too sticky. The wham bam PEX is perfect, though it took a few heating+cooling cycles to reach prime stickiness. I've only had one failed print since switching (and the failure happened in a known low spot on the bed). Highly recommend.

R
Robert Larrarte
Great product

This build plate is great , I have no adhesion issues with anything.So far tried PLA,PETG ,ASA,PETG CF.
Thanks for the great product.

J
Jayson Smith
Billiant! Made my life easier!

I have older machines that are absolute workhorses.
But the Taped unremovable plate made life difficult when the tape was new, prints had to be yeated out of the machine.
Now I just wait for the plate to cool, and the print just gently pops off the WHAMBAM PEX plate.
Also worth noting, I havent had the need to use a brim or raft for supports since getting the PEX plate for these machines.
The adheasion is incredible!