•
1 9

300 x 300 Kit with Pre-Installed PEX Build Surface - LulzBot Taz Pro & Taz Workhorse, & Taz 3, 4, 5, 6

$93.00 USD
$93.00 USD
Sale Sold out
Shipping calculated at checkout.
In stock (226 units), ready to be shipped

Description

Size 300mm x 300mm / 11.8" x 11.8"

*Fits: LulzBot TAZ Workhorse, TAZ Pro, Taz Pro XT, TAZ 6, TAZ 5, TAZ 4, TAZ 3

*may fit: Anet A8 plus, Anet et5 and et5 pro

The Pre-Installed Flexible Build System includes:

  • 1  Wham Bam Flexi Magnetic Base (high temp-resistant up to 150 degrees with high temp 3M adhesive)
  • 1  Wham Bam Flexi Build Plate (spring steel) with pre-installed Wham Bam Custom Formulated PEX Build Surface
  • 1 Steel Wool 000 (for prepping your PEX Build Surface)

The Pre-Installed Double Wham includes:

  • 1  Wham Bam Flexi Magnetic Base (high temp-resistant up to 150 degrees with high temp 3M adhesive)
  • 2  Wham Bam Flexi Build Plate (spring steel) with pre-installed Wham Bam Custom Formulated PEX Build Surface
  • 1 Steel Wool 000 (for prepping your PEX Build Surface)

    For more information on this product, click here: Flexible Build System

    View the full chart of filament settings on PEX

    *Attention: It is the buyer’s responsibility to be sure the size selected will work on your machine. Measure your bed, do not rely on build volume and see if you are happy with the size before ordering. Please keep in mind that on one side you will have 2 tabs that stick out another 15mm. Wham Bam is not responsible for mistaken order sizes. 

    **It is the buyer’s responsibility to pay any taxes and import duties. No refunds of uncollected customs packages.

    Customer Reviews

    Based on 2 reviews
    50%
    (1)
    50%
    (1)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    A
    Anthony Farone
    Good & Bad in the Same Breath

    I am a Fan of the Wham Bam Flexible Build System.

    1st Purchase was a Double Wham for my Elegoo Saturn 2 Resin Printer. This has been working flawlessly.

    2nd Purchase was a Double Wham for my Taz 6 FDM Printer. Everything installed as expected. Was using the 1st Flexible Plate and was getting fantastic "glass looking" surfaces on PLA (various manufacturers) Prints... as well as with ColorFab nGen (nylon) filament. My wife then asked me to print something for outside use in the garden. For these prints I typically use a Taulman T-Glass filament for exterior use. Used all the typical settings for the T-Glass and when I went to remove the print from the Flexible Plate with PEX - the print popped off as expected - but the surface of the PEX was somewhat damaged. There are now indentations and marks within the PEX surface from this (1) singular print. When I started a new PLA Print, the marks within the PEX transferred to the 1st layer of the print. Very disappointing. So much for the Glass Finish that I was expecting.

    I then pulled out the 2nd Flexible Plate (unused) that was part of the Double Wham purchase and there are multiple scratches within the PEX surface that will ultimately do the same thing... transfer to the 1st layer of the print. Again... Very Disappointing.

    Note that using the supplied steel wool will Not remove these defects from either Flex Plate PEX surface. The Good - I like the Flex Plate addition to my FDM Printer. The Bad - I Don't like that a singular print on Flex Plate 1 rendered damaged... and Flex Plate 2 was actually scratched coming out of the original packaging.

    B
    Buddy
    Installed easily as documented, fits perfectly, works very well.

    Installed easily as documented, fits perfectly, works very well.